How To Fix A Delta Shower Head Without Set Screw

The Delta Monitor single handle for the shower is a popular choice for many. However, some users have faced issues with removing the handle due to the absence of a set screw. In such cases, it is recommended to check for a hidden pop-off panel or a small Allen set screw that may require rotating the handle to become visible. If the screw is not found, applying more force to wiggle or pop the handle off may be necessary, but this should be done with caution to avoid breakage.

Delta Monitor single handle shower set screw removal

If you are trying to remove the set screw from your Delta Monitor single-handle shower head, there are a few things you can try. Firstly, check if there is a cap on the shower handle that you can pop off, revealing a Phillips screw that you can then unscrew. If you cannot see a cap, try using a small Allen wrench to loosen the screw. If the screw is stuck, try spraying some penetrating oil or vinegar around the screw and leave it to soak for a while before trying again. You could also try using a pair of side cutters to hold the short end of the Allen key to get more torque. If the screw is still not budging, you may need to resort to drilling it out.

Delta shower faucet with no set screw

If you are trying to remove a Delta shower faucet with no set screw, there are a few methods you can try. Firstly, check the front or tip of the handle for a cap, as some Delta fixtures are very good at concealing them. If there is no cap, try rotating the handle to check for a tiny Allen set screw on the side, which may be difficult to spot. If you still cannot find a set screw, try applying more force to wiggle the handle off, as it may just need a little extra force. If the handle is still stuck, you can try using a handle puller to distribute your pull more evenly across the handle.

If your Delta shower faucet is still not coming off, you can try using a solvent like CLR or white vinegar and water on a rag, and letting it soak for a couple of hours. You can also try heating the metal with a blowtorch or heat gun and then sliding the handle off. As a last resort, you can try cutting the handle off with a hacksaw, but this will require you to purchase new faucet hardware and possibly a new cartridge.

Delta shower handle with no set screw or pop-off panel

If you're looking to remove a Delta shower handle with no set screw or pop-off panel, there are a few things you can try. Firstly, check the front or tip of the handle for a cap, as some higher-end fixtures are very good at concealing them. If there is a cap, you can try popping it off and then unscrewing the Phillips screw underneath.

If there is no cap, look for a tiny Allen set screw along the side of the handle—you may need to rotate the handle to find it. If you still can't find a screw, try using a small Allen wrench to apply some force and wiggle the handle off.

If none of these methods work, you may need to consult a plumber or a specialist forum for further advice.

Delta Monnor shower handle screw removal

If you're trying to remove the handle of a Delta Monitor shower and are having trouble locating or unscrewing the set screw, there are a few things you can try.

First, make sure you have the correct size Allen key for the set screw. If the Allen key is too small, you can try using a pair of side cutters to hold the short end of the key to get more torque. Alternatively, you can use a "T" handle Allen wrench or grab a pair of vice grips to hold the Allen wrench and break the screw loose. If you don't have an Allen key, you can try using a Phillips-head screwdriver or a Torx screwdriver.

If the screw is stuck, you can try spraying some penetrating oil, such as WD-40, or vinegar around the screw and letting it sit for a while before trying again. You can also try wrapping a tight rag soaked in penetrating oil around that area of the handle. If the screw is rusted, you can try using CLR to loosen the corrosion.

If the screw is stripped, you can try using a screw extractor to remove it. If that doesn't work, you may need to drill out the screw. Make sure to use a drill bit extension to give the drill enough clearance over the shower handle. Be careful not to drill into the cartridge, as you will need to replace it if it is damaged.

Once the screw is removed, you should be able to slide off the rest of the handle assembly. If it's stuck, try rocking the handle side to side and up and down while also pulling outwards. You can also try spraying it with a penetrant like PB Blaster.

If you're still unable to remove the handle, you may need to cut it off with a saw or a hacksaw. This should be done carefully to avoid damaging the cartridge or the valve.

Delta shower handle set screw replacements

If the set screw on your Delta shower handle is damaged or missing, you can purchase a replacement from hardware stores or online. The Delta Pair of Tub and Shower Handle Set Screws in Chrome, for example, is a genuine Delta repair part that can be bought from Home Depot.

If your Delta shower handle has no set screw and you are looking to remove it, you can try the following methods:

• Pop off the cap of the shower handle and unscrew the Phillips screw inside.
• Use an Allen wrench to unscrew the set screw. If it won't budge, try using a larger Allen wrench with pliers or channel locks for extra torque. You can also try a "T" handle Allen wrench.
• If the set screw is frozen due to calcium or deposit buildup, spray some vinegar or penetrating oil directly onto and around it. Let it soak and try again.
• As a last resort, you may need to saw through the handle or drill out the set screw.

Frequently asked questions