Dji Inspire 1 Motor Mount Screw Size: A Comprehensive Guide

The DJI Inspire 1 motor mount screw size is a topic of much discussion and speculation among drone enthusiasts. While some sources claim that the correct size is T8 or T9, others suggest that it is Phillips #000 or #00. There are also reports of M3 and M2.5 metric screws being used in the motors and to secure the top and bottom halves of the drone, respectively. It is important to note that over-tightening of screws can lead to damage, and the use of thread locker is recommended to secure screws and prevent loosening due to vibration.

The correct screwdriver for the DJI Inspire 1 motor mount screw is a T8

The DJI Inspire 1 is a high-quality drone with a sophisticated design. However, like any piece of machinery, it may occasionally require maintenance or repairs. When it comes to the motor mount screws, it is essential to use the correct tools to avoid damage and ensure a secure fit.

The motor mount screws on the DJI Inspire 1 require a specific type of screwdriver for proper installation and removal. The correct screwdriver for these screws is a T8 Torx screwdriver. Using the right size screwdriver is crucial to avoid stripping the screw head, which can make it difficult to remove the screws and may require replacement parts.

Some users have reported that a T9 Torx screwdriver can also fit the motor mount screws. However, it is important to note that using a T9 screwdriver may increase the risk of stripping the screw head. Therefore, it is always recommended to use the T8 size to ensure a precise and safe fit.

It is worth mentioning that the process of removing the motor mount screws can be challenging due to the strong thread locker used by DJI. To facilitate the removal process, it is advisable to apply heat to the screw head using a hair dryer or soldering iron. This helps to break down the thread locker, making it easier to loosen the screws. Always exercise caution when applying heat to avoid damaging the motor or surrounding plastic components.

In summary, for the DJI Inspire 1 motor mount screws, the correct screwdriver size is a T8. Using the appropriate tools and techniques will help ensure a smooth and successful maintenance experience.

The screws are metric

The screws used in the motors of the DJI Inspire 1 are metric. The screw size for the motors is M3, while the screws that secure the top and bottom halves are M2.5.

When working with these screws, it is important to be careful and not force them if they become bound. It is also recommended to use plastic-safe Loctite to prevent the screws from becoming stuck and to be cautious not to over-tighten them, as this can cause damage.

If you need to remove the screws, it is suggested to use a high-quality Torx driver with a good tight fit and to apply some heat to the bolt head to help break the thread locker free. You can use a hair dryer or soldering iron for this, being careful not to apply direct heat to the motor.

Additionally, when applying Loctite, be sure to apply it only to the tips of the screws and let it dry completely before installing them. This will help prevent the plastic motor mounts from cracking.

The screws are M3

The screws that secure the motor mounts on the DJI Inspire 1 are M3. This is the most common screw size used in the Inspire 1, with M2.5 screws also used in some areas.

When working with these screws, it is important to be cautious and apply slow, consistent pressure. The thread locker used on the bolts is very strong, and improper removal techniques can result in stripped bolt heads or broken bolts. It is recommended to use a high-quality Torx driver with a good tight fit, and to apply heat to the bolt head to help break the thread locker free. A hair dryer or soldering iron can be used for this purpose, but care must be taken to avoid damaging the motor or plastic components.

When using Loctite, it is important to apply it only to the tips of the screws and let it dry completely before installing them. The fumes from the curing process can damage the plastic motor mounts and cause cracking. Plastic-safe Loctite is available and can help prevent this issue. Additionally, it is recommended to apply Loctite just prior to assembly, as applying it too far in advance can make the plastic brittle and cause chipping when the screws are threaded in.

It is also worth noting that some Inspire 1 users have reported issues with poor quality screws. There have been cases where screws have sheared off or stripped unexpectedly, possibly due to over-tightening or vibration fatigue. Regular inspections and maintenance are important to identify and address any potential issues.

The screws are very tight

If the screws are very tight, there are a few methods you can try to loosen them. Firstly, it is recommended to use a high-quality Torx driver with a good tight fit. You can try using a T8 or T9 Torx driver, but be aware that using a T8 driver may risk stripping the head. If the screw is already damaged, you may need to replace the motor entirely.

Another method to loosen tight screws is to apply heat to the bolt head. You can use a hair dryer, a soldering iron, or a soldering gun to heat the screw, but be careful not to direct the heat towards the motor, as this could cause damage. Instead, heat the tip of the driver and then insert it into the screw, allowing the heat to transfer and soften the glue.

Additionally, you can try using some thread locker on the screws. Apply the thread locker to the tips of the screws only and let it dry completely before installing them. Be cautious not to over-tighten the screws, as this could lead to damage.

If you are still unable to loosen the tight screws, you may need to seek professional help or contact the DJI repair center for further assistance.

The screws are glued with threadlock

Threadlocking solutions are used to lock and seal threaded assemblies, protecting against vibration, corrosion, and galling. The screws on the DJI Inspire 1 motor mount are glued with threadlock, which is a strong adhesive that can be difficult to remove. To remove the screws, it is recommended to use a high-quality Torx driver with a good tight fit and apply some heat to the bolt head to help break the thread locker free. A hair dryer or soldering iron can be used to apply heat, but it is important to be careful and use slow, consistent pressure when turning the driver to avoid breaking the bolts.

Threadlock is available in different strengths and formulations, including low, medium, and high strengths, and can be applied in liquid or semi-solid stick form. It is important to choose the appropriate type of threadlock for your specific application. For the DJI Inspire 1 motor mount screws, a medium-strength threadlock is recommended. This will allow for disassembly with standard hand tools without the need for heat. The threadlock should be allowed to cure for 24 hours for optimal sealing power.

When applying threadlock to the DJI Inspire 1 motor mount screws, it is important to follow the manufacturer's recommendations for the specific type of threadlock being used. It is also crucial to exercise caution when working with the screws, as improper techniques can result in stripped bolt heads or damage to the motor, plastics, or mounts.

Overall, the use of threadlock on the DJI Inspire 1 motor mount screws provides a secure and effective solution for keeping the assembly in place and preventing loosening. However, it is important to be aware of the challenges that may arise when attempting to remove the screws and to follow the recommended techniques for safe and successful disassembly.

Frequently asked questions