Dji Matrice M600 And Ronin-Mx: Understanding Screw Sizes And Compatibility

The DJI Matrice 600 is a six-rotor system with a maximum payload of 6.0 kilograms, making it ideal for a range of gimbals and cameras. When paired with the Ronin-MX gimbal, the M600 offers best-in-class three-axis aerial video stabilisation. The Ronin-MX can be mounted on the M600 in minutes, allowing for seamless transitions between handheld and aerial footage. The screw size for the M600 and Ronin-MX is not publicly available, but the M600 requires an M3*6 screw to attach the expansion bay connectors to the expansion bays carbon board, and an M3*8 screw to fasten the expansion bay connectors.

Screw size for attaching the Ronin-MX to the M600

The screw size for attaching the Ronin-MX to the M600 is not publicly available. However, there are detailed instructions available for mounting the Ronin-MX to the M600.

Firstly, the Ronin-MX must be mounted to the aircraft. Then, the motor should be attached. The focus accessory support frame is optional but can be used if necessary. The position of the motor should be chosen based on the weight and centre of gravity of the lens and camera.

The expansion module power and data cable should then be connected. One end of the cable should be connected to the communication interface on the motor, and the other end to the P-Tap interface and Lightbridge interface. If using the focus with the remote start/stop, a special cable is required. One end of this cable should be connected to the communication interface on the motor, and the other side to the PWR on the remote start/stop.

Finally, all devices should be turned on. The LED will turn solid green when the motor expansion module is ready for use.

M3*6 screws for attaching expansion bay connectors

The DJI Matrice 600 is a sophisticated aircraft with industrial and filmmaking applications. It is designed to fly the Ronin-MX gimbal and is also compatible with all of DJI's Zenmuse gimbals and cameras. The Ronin-MX can be mounted on the Matrice 600 in minutes, allowing for easy transition from handheld to aerial footage.

To attach the Ronin-MX gimbal to the Matrice 600, you will need M3*6 screws. These screws are used to attach the expansion bay connectors to the expansion bays carbon board. There are two different types of expansion bay connectors, so it is important to distinguish between them during installation. The fixed connectors should be mounted near the nose, while the movable connectors should be mounted near the tail.

The M3*6 screws are also used to attach the four gimbal connectors to the expansion bay carbon board. It is important to note that the gimbal connectors will tilt forward. Additionally, M2*5 cruciform screws are needed to attach the gimbal mounting bar to the gimbal mounting board.

The installation process for the Ronin-MX on the Matrice 600 is straightforward and can be completed in a few simple steps. First, remove the centre frame's top cover, being careful not to damage the fan cable. Disconnect the power cable from the landing gear and remove the centre frame's bottom cover. Pass the Ronin-MX gimbal's cable through the hole on the aircraft body's bottom board and connect it to the Lightbridge 2's gimbal cable port. Connect the fan's power cable and mount the centre frame top cover. Mount the centre frame bottom cover.

The DJI Matrice 600 is a powerful platform for filmmakers and industrial applications, offering versatility and ease of use. With its compatibility with the Ronin-MX gimbal and various screws readily available, users can quickly set up their equipment and focus on capturing stunning visuals.

M3*8 screws for fastening expansion bay connectors

The DJI Matrice 600 is a sophisticated aircraft with multiple applications. It can be used for industrial purposes as well as for filmmaking. The M600 is designed to fly the Ronin-MX gimbal and is also compatible with other DJI Zenmuse gimbals and cameras.

When mounting the Ronin-MX gimbal to the M600, you will need to follow specific steps to ensure a secure and stable connection. One of the critical components of this process is using the correct screws.

For fastening the expansion bay connectors, M3*8 screws are required. These screws are essential to securely attach the expansion bay connectors to the carbon board. It is important to note that there are two different types of expansion bay connectors, and they should be distinguished during installation. The correct placement of the connectors is crucial, with the fixed connectors mounted near the nose and the movable connectors installed near the tail of the aircraft.

M3*8 screws are readily available in the market and can be purchased online from retailers like Amazon and Home Depot. They come in various materials, including stainless steel and alloy steel, and are often sold in packs of different quantities. When purchasing, ensure that you select the appropriate type and size of screw for your specific application.

M2*5 cruciform screws for attaching gimbal mounting bar

The M2*5 cruciform screws are used to attach the gimbal mounting bar to the gimbal mounting board. This is done after the Zenmuse X5 gimbal's 7PIN cable has been passed through the hole on the aircraft body's bottom board and connected to Lightbridge 2's gimbal cable port. The gimbal mounting bar should not be attached when installing an X3 or XT camera. However, one gimbal mounting bar should be mounted when installing the X5 camera, and two gimbal mounting bars should be mounted when installing the X5R camera.

To attach the gimbal mounting bar, first mount the gimbal quick release plate onto the gimbal mounting board. Line up the 3PIN port and 7PIN port on the reserved hole of the gimbal mounting board. Then, attach the vibration dampers to the reserved holes on the gimbal connector. Install the gimbal mounting plate onto the vibration dampers on the gimbal connector. Cut each side of the vibration dampers evenly. Remove the crossbar on the expansion tubes and mount the expansion bay onto the expansion tubes. Use M3*8 screws to fasten the expansion bay connectors.

The M2*5 cruciform screws are a crucial component in the process of attaching the gimbal mounting bar to the gimbal mounting board, ensuring a secure and stable connection between the two parts.

1.5mm hexagonal socket screwdriver for removing interface module screws

To remove the interface module from the remote controller of the DJI Matrice 600, you will need a 1.5mm hexagonal socket screwdriver. This is a crucial tool for this task, as it allows you to remove the four screws on the interface module. Once these screws are taken out, you can proceed with the rest of the process, which includes removing the SDI port cover, counterclockwise rotation of the metal fixing rings, and eventually taking out the internal PCB board.

The 1.5mm hexagonal socket screwdriver is a specialty tool designed for working with small, precise screws often found in electronics and devices. It is an essential item for anyone performing maintenance or repairs on the DJI Matrice 600, as it provides the ability to access and adjust internal components. This screwdriver is also useful for other applications, such as computer hardware, camera equipment, and even certain models of eyeglasses and watches.

When choosing a 1.5mm hexagonal socket screwdriver, it is important to consider the quality and precision of the tool. Look for screwdrivers made from durable materials, such as chrome-vanadium steel, which can provide a secure grip on the tiny screws without causing damage. Additionally, a compact and portable screwdriver set can be convenient, especially when you need to carry it to a worksite or during travel.

It is always a good idea to have the right tools for the job, and in this case, the 1.5mm hexagonal socket screwdriver is an indispensable tool for removing the interface module screws of the DJI Matrice 600. This screwdriver ensures you can safely and effectively disassemble the remote controller, following the manufacturer's instructions, and perform any necessary adjustments or repairs.

Frequently asked questions