Droid Maxx 2 Screw Sizes: A Complete Guide

The Motorola Droid Maxx has a total of 11 screws, including eight black screws spread across the motherboard, four at the top and four at the bottom, and two silver screws located at the right lower part of the device. There is also one screw holding the camera housing, which is a T4 screw.

Droid Maxx's T4 screw located by the camera

The T4 screw located by the camera on the Droid Maxx is slightly longer than the other screws holding the phone together. It is used to hold the camera housing in place. This screw can be defective, with some users reporting that it does not have the torx head cut into it, instead having a smooth surface that makes it difficult to remove.

To replace the front-facing camera of the Droid Maxx, you will need to remove this T4 screw. First, place the Droid Maxx face-up on a soft, flat plastic surface. Then, tilt the phone to the right to see the edge of the rubber back case. Next, use a spudger to press and slide along the space between the rubber case and the Droid Maxx frame until you hear a "snap" sound. Rotate the phone if necessary to facilitate your movement.

Once the top part of the case is separated from the frame, grip the bottom part of the rubber case and slide it down to remove it completely. Now, lay the Droid Maxx face down on the plastic surface and remove all the screws in the motherboard, including the T4 screw holding the camera housing. There are a total of eight black screws on the motherboard (four at the top and four at the bottom) and two silver screws located at the right lower part of the phone.

After removing all the screws, locate the two tabs in the camera plastic housing, one at each corner of the Droid Maxx. Use a flathead driver to gently lift both tabs to release the camera housing, being careful not to break the delicate plastic tabs.

To replace the rear-facing camera, you will need to lift the motherboard from the assembly, which may require softening the adhesive with a gun heater. Then, use a spudger to lift up the anti-static tape covering the camera connectors and remove the tape. Finally, use a plastic opening tool to lift up the tab on the front-facing camera and push the camera out.

Droid Maxx's camera housing screw

The Droid Maxx's camera housing screw is located on the back of the phone, underneath the rubber back case. To access the screw, you will need to remove the back cover.

Removing the Back Cover

Place the Droid Maxx face up on a soft, flat plastic surface. Lift the phone and turn it 90 degrees to your left, holding it by the sides with one hand. With your free hand, take a spudger and insert it into the upper gap between the volume buttons and the case. Press the flat part of the spudger's tip firmly against the case until you hear a "snap" sound. Carefully remove the volume buttons with your two fingers, being careful not to bend or force the part, as it also serves as a tray for the SIM card.

Next, tilt the Droid Maxx to the right so you can see the edge of the rubber back case. Press the tip of the spudger against the space between the rubber case and the frame, and slide the spudger's edge along the surface until you hear another "snap" sound. Work your way to the top of the phone, using your fingers to support the removal of the upper part of the rubber back case. Rotate the phone if necessary to facilitate your movement.

Once the top part of the case is separated from the frame, grip the bottom part of the rubber case and slide it down to remove it completely. Place the rubber back case nearby, out of the way of your arm's motion.

Removing the Camera Back Housing

Lay the Droid Maxx face down on the plastic surface to begin removing the screws. You will need a Torx T5 Screwdriver to remove the black screws from the motherboard and a T4 screwdriver for the camera housing screw. There are a total of eight black screws on the motherboard (four at the top and four at the bottom) and two silver screws located on the lower right. After removing all the screws, lift and hold the Droid Maxx as before.

Locate the two tabs in the camera plastic housing, one at each corner of the phone. Take a flathead driver and gently lift both tabs to release the camera housing. Be very careful, as these plastic tabs are delicate and can break easily.

With the camera housing screw removed, you can now proceed to replace or repair the camera. Remember to follow the steps in reverse order to reassemble your Droid Maxx.

Droid Maxx's motherboard screws

The Motorola Droid MAXX 2 is a smartphone that was released in October 2015. It has a 5.5-inch Gorilla Glass screen and a plastic body. The phone's motherboard is located underneath the display assembly.

To access the motherboard, you will need to remove the display assembly, which is secured to the frame with adhesive. A heat gun can be used to warm up and loosen the adhesive. Once the display assembly is removed, the motherboard can be carefully detached by disconnecting the cables connected to it.

When working on the motherboard, it is important to handle it with care and avoid touching any of the electronic components directly, as this can cause damage. Additionally, keep track of the screws removed during the disassembly process, as they will need to be replaced in the correct order and orientation during reassembly.

The specific screw sizes for the Droid MAXX 2 motherboard are not readily available. However, it appears that the phone uses Torx screws, specifically the T4 type, based on a user's experience with repairing the device. This user also mentioned that the T4 screw located by the camera was defective and lacked the typical Torx head, requiring the use of an extraction tool for removal.

When working with screws, it is important to use the correct tools and techniques to avoid stripping or damaging the screws. Using the appropriate screwdriver type and size is crucial, as well as applying the right amount of torque during tightening or loosening.

Droid Maxx's rubber back case

If you're looking for a rubber back case for your Droid Maxx 2, there are a few options available on Amazon.

The first is the Matte Silicone Case, which comes in black and is available with free delivery on orders over $35. This case currently only has 3 left in stock, so you'll need to order soon to avoid missing out.

Another option is the Speck Products Candy Shell Grip Case, which comes in Pool Blue/Deep Sea Blue. This case also has free delivery on orders over $35 and, at the time of writing, has 3 new offers available from $8.47.

If you're looking for a more robust case, the OTTERBOX DEFENDER SERIES Case might be a good option. This case comes in Melon Pop (Sage Green/Hibiscus Pink) and has a 4.2-star rating from 119 reviews. It features a synthetic rubber outer slipcover and a polycarbonate inner shell for added protection. It also has port covers to keep out dust and debris and is available with free delivery on orders over $35.

There are also some non-rubber options available, including hard polycarbonate cases and dual-layer protective cases.

Droid Maxx's volume buttons

The Motorola Droid MAXX 2 is a smartphone that can be taken apart for repairs. The volume and power buttons are housed within the mid-frame of the device. To access the buttons, you must first remove the sim card tray and back cover. Then, remove the seventeen 3.2mm Torx T4 screws from the mid-frame. If you are having trouble unscrewing these, try using a T3 bit instead.

Once the mid-frame is removed, the volume and power buttons will be easily accessible. It is important to keep track of these buttons when taking the phone apart, as they are likely to fall out when the halves are separated.

If you are looking to replace the volume and power buttons, you can follow the steps outlined above in reverse order to reassemble the device.

In addition, if your Droid MAXX 2 is frozen or unresponsive, you can force a reboot by simultaneously pressing the power and volume down buttons for approximately 10 seconds. This will not delete any information on your device.

Frequently asked questions