Screw Size For Terminal Block: Dryer Repair Essentials

The 279393 Dryer Terminal Block Screw Kit is a crucial component for your dryer, responsible for securing the power cord to the terminal block. This kit typically includes three screws and three nuts, and it is compatible with a range of dryer models from brands like Whirlpool, Kenmore, and Maytag. Proper installation of this kit is essential to ensure your dryer functions safely and efficiently, preventing electrical issues that could lead to potential fires.

Screw dimensions

The screw dimensions for the 279393 Dryer Terminal Block Screw Set are 7/16"L x 7/16"W x 11/16"H. The set includes three screws and three nuts, and is used to connect electric dryer terminal wires to the terminal block. It is compatible with some Admiral, Amana, Kenmore, KitchenAid, Maytag, Roper, and Whirlpool dryer models.

The 279393 Dryer Terminal Block Screw Set is an essential part of your dryer, as it connects the dryer's power cord to the internal wiring of the dryer. It is important to ensure that the screws are tight to prevent electrical problems, which can be dangerous and even lead to fires.

When replacing the terminal block screws, it is important to follow the correct procedure. First, unplug your dryer from the electrical outlet. Then, locate the terminal block, which is usually at the back of the dryer. Remove the old screws and nuts holding the terminal block in place, and install the new screws and nuts from the 279393 kit. Tighten the screws to ensure a secure connection, and finally, plug your dryer back in.

The 279393 Dryer Terminal Block Screw Set is an affordable and straightforward solution to ensure your dryer is safe and functioning properly.

Nut dimensions

The nut plays a crucial role in fastening the dryer's terminal block securely. When replacing the terminal block screws, it is important to ensure that the nuts are properly aligned and tightened to prevent any electrical issues or safety hazards. The nuts should be inserted into the terminal block, followed by the repositioning of the terminals and the bending back of their locking tabs for a secure hold.

It is worth noting that the nut dimensions provided are specific to the 279393 Dryer Terminal Block Screw Kit. Different dryer models may have varying nut sizes, so it is always important to check the compatibility of the replacement parts with your specific dryer model.

Additionally, when working with nuts and screws, it is recommended to wear protective gloves to prevent any injuries. It is also important to clean up any spills or messes immediately to avoid potential electrical hazards.

Compatibility with Whirlpool

The Whirlpool 279320 Terminal Block for Dryers is compatible with multiple Whirlpool models, including LTE5243DQ, NED7200TW, MDE2400AZW, MDE9700AYM, and MDE9700AYW. This terminal block is designed specifically for Whirlpool appliances and meets the engineering standards set by the manufacturer.

The Whirlpool 279320 Terminal Block is an OEM (Original Equipment Manufacturer) part, ensuring it is a genuine replacement component. This terminal block is used to connect the power cord to the dryer, and it includes wires, terminals, screws, nuts, and instructions for installation. The screws included in the kit are 7/16" long, 7/16" wide, and 11/16" high, with the nuts measuring 1/2" long, 1/2" wide, and 1/8" high.

In addition to Whirlpool, this terminal block is also compatible with several other brands, such as Admiral, Amana, Crosley, Estate, Inglis, Kenmore, KitchenAid, Magic Chef, Maytag, and Roper. It is important to check the compatibility of the kit with your specific dryer model to ensure a correct replacement.

The Whirlpool 279320 Terminal Block is a well-tested and high-quality part that comes with a one-year warranty from the manufacturer. This product has received positive reviews from customers who found it easy to install, with some mentioning that it works perfectly and fits their dryer model exactly.

Installation process

The installation process for a dryer terminal block screw set involves several steps and requires some basic tools for the job. Here is a detailed guide on how to install the 279393 Dryer Terminal Block Screw Kit, which is compatible with various dryer models from brands like Whirlpool, Kenmore, Maytag, and more:

Step 1: Unplug the Dryer

Begin by disconnecting your dryer from the electrical outlet to ensure safety during the installation process. This is an important precaution to prevent any electrical hazards.

Step 2: Locate the Terminal Block

The terminal block is usually located at the back of the dryer. It is where the dryer's power cord connects to the internal wiring of the appliance.

Step 3: Remove Old Screws and Nuts

Using a suitable screwdriver, remove the old screws and nuts that are currently holding the terminal block in place. This will allow you to access the terminal block for the next steps.

Step 4: Install New Screws and Nuts

Take the new screws and nuts provided in the 279393 kit. Start screwing them in place to secure the terminal block. Make sure to tighten the screws adequately to ensure a secure connection.

Step 5: Re-connect the Dryer

Once the new screws and nuts are in place, you can plug your dryer back into the electrical outlet. Your dryer is now ready to use with its new terminal block screw set.

Additional Tips:

• Always check the compatibility of the screw kit with your dryer model before purchasing.
• Wear work gloves during the installation process to protect your hands from potential hazards.
• Clean up any messes or spills immediately to prevent damage to the appliance.
• If you're unsure about the installation process, seek guidance from a professional or a repair manual specific to your dryer model.
• Keep children and pets away from the work area, and ensure they do not have access to any small parts or tools.

By following these steps and staying cautious, you can successfully install the dryer terminal block screw set and ensure your appliance is functioning properly and safely.

Troubleshooting

Identify the Problem:

Start by identifying the specific issue you're facing with your dryer. It could be that the dryer is not turning on, or you may have noticed loose or damaged terminal block screws. In some cases, the dryer might be tripping the breaker, which could be due to loose or damaged wires on the terminal block.

Check Compatibility:

Before purchasing a replacement screw kit, it's crucial to ensure that it is compatible with your dryer model. The 279393 Dryer Terminal Block Screw Kit, for example, is compatible with various brands, including Whirlpool, Kenmore, Admiral, Amana, Crosley, Estate, Inglis, KitchenAid, Magic Chef, Maytag, and Roper. Check your dryer's model number to confirm compatibility.

Gather the Right Tools:

To replace the terminal block screws, you'll need a few basic tools. These typically include a Phillips head screwdriver, a small flathead screwdriver, a wrench or pliers, and work gloves for safety. Additionally, you might need a 5/16-inch socket or nut driver to unscrew the terminal block's cover plate.

Disconnect Power and Prepare for Replacement:

Safety should always come first when working with electrical appliances. Before proceeding, unplug your dryer from the electrical outlet to ensure there is no power running through it. Then, locate the terminal block, usually found at the back of the dryer.

Remove Old Screws and Nuts:

Using the appropriate tools, carefully remove the old screws and nuts holding the terminal block in place. You may need to untangle and remove the old screws securing the power cord wires with a Phillips head screwdriver. Additionally, you might need to remove mounting screws with a small flathead screwdriver by bending their locking tabs to unfasten the terminals and easily remove the old nuts.

Install New Screws and Nuts:

Once the old screws and nuts are removed, it's time to install the new ones. Insert the new nuts into the terminal block, ensuring they are securely in place. Then, reposition the terminals and bend back their locking tabs. Reinstall the terminal block by fastening it to its brackets using mounting screws.

Secure Connections and Reattach Cover:

After installing the new screws and nuts, ensure all connections are secure. Thread the screws loosely, align the power cord wires, and then tighten the screws with a wrench or pliers. Finally, reposition the terminal block cover plate and rethread its screw.

Test the Dryer:

Once you've completed the replacement, plug your dryer back into the power outlet. Test the dryer to ensure it's functioning correctly and that the issue has been resolved.

Remember to follow safety precautions and refer to your dryer's user manual for model-specific instructions if needed. If you're unsure about any steps or encounter complications, don't hesitate to consult a professional for assistance.

Frequently asked questions