Faucet Screw Sizes: Standardizing Your Plumbing Experience

Faucet screw sizes vary depending on the brand and model of the faucet. For example, the most common faucet has a screw at the bottom of its handle that measures 3/8 inch in diameter. The Delta single-handle faucet set screw size is #10-32 X.5. The Moen kitchen faucet set screw size is typically 7/64th, and the handle adapter can be removed using a screwdriver after the set screw is removed. The Danco #46 Faucet Handle Screw is designed for easy installation and made from durable metal.

Delta faucet RP25620 set screw

The Delta Faucet RP25620 set screw is a replacement screw for Delta faucet handles. It is designed exclusively for Delta faucets and is made to the original specifications. The screw is rigorously tested to ensure quality performance.

The RP25620 set screw is compatible with a range of Delta faucet models, including the T14038 Shower Fixture, T14051 Shower Fixture, T14092 Shower Fixture, T14238 Shower Fixture, T14251 Shower Fixture, and more. It is also compatible with some Delta kitchen faucet handles.

The screw is available in a set of two and requires an Allen wrench for installation, which is sold separately. The dimensions of the screw are 0.13 x 0.13 x 0.13 inches, and it is a #10-32x.25 UNF-3A screw.

The Delta Faucet RP25620 set screw is available from a variety of retailers, including Amazon, eReplacementParts.com, The Home Depot, and Edmondson Supply. Prices range from $1.95 to $5.10, with some retailers offering discounts or free shipping.

Hex wrench size for Moen kitchen faucet

If you need to replace a part in a Moen kitchen faucet, you will likely need a hex wrench to remove the specific part. In most cases, the hardware used by Moen requires a 7/64-inch hex wrench. This applies to Moen Renzo faucets, handle set screws for single-handle kitchen faucets, and PosiTemp levers for Moen showers.

You can also use a 10mm wrench for a Moen faucet. However, some users have reported that a 7/64-inch wrench is the best bet.

Moen also offers a commercial hex key wrench (model 104447) that can be used for installing and working on Moen commercial faucets 8305, 8306, and 8307.

Removing a Delta faucet screw

Step 1: Turn Off the Water Supply

Before starting any work on your faucet, it is crucial to turn off the water supply to avoid leaks or accidents. Locate the hot and cold water valves under the sink and turn them clockwise as far as they will go. This will ensure that the water flow to the faucet is completely shut off.

Step 2: Locate the Set Screw

The set screw is typically found at the base of the faucet handle. It is usually a small screw that holds the handle in place. You may need to remove a decorative cap or cover to access it. If you have a Delta single-handle faucet, the set screw is often located underneath the faucet.

Step 3: Prepare the Tools

To remove the set screw, you will need an Allen wrench or a small screwdriver, depending on the type of set screw your faucet has. The most common size for a Delta faucet set screw is #10-32 x.25 UNF-3A, which requires a 3/32-inch Allen wrench. However, some Delta faucets may use different sizes, so it is recommended to check your faucet's specifications or consult the owner's manual.

Step 4: Loosen the Set Screw

Insert the appropriate Allen wrench or screwdriver into the set screw and turn it counterclockwise to loosen it. If the screw is tight, you may need to apply some force, but be careful not to strip the screw head. You can also try using a corrosion-eliminating liquid or lubricating the screw with WD-40 to make it easier to turn.

Step 5: Remove the Handle

Once the set screw is loosened, you can remove the faucet handle. Gently pull or wiggle it off the stem. If it is stuck, try using a rubber mallet to gently tap it loose. Be cautious not to use excessive force, as this may damage the faucet or the handle.

Step 6: Clean and Inspect

With the handle removed, take the opportunity to clean the area and inspect the O-rings, gaskets, and other components for any signs of wear or damage. Replace any worn-out parts to ensure your faucet functions properly and doesn't leak.

Step 7: Reassemble

After making any necessary repairs or replacements, it's time to reassemble the faucet. Screw in the set screw securely, but avoid overtightening it. Reattach the handle by sliding it back onto the stem and securing it in place. Turn on the water supply valves and test your faucet to ensure it is functioning correctly.

DANCO faucet bibb screws

Danco offers a range of faucet bibb screws for repairing broken or leaking faucet handles. The screws are made of durable metal and come in a variety of sizes, including:

• #10 Faucet Bibb Screw 3/8 X 10-32
• #11 Faucet Bibb Screw 1/2 X 10-32
• #13 Faucet Bibb Screw 3/8 X 10-28
• #16 Faucet Bibb Screw 3/8 X 10-24 (available in packs of 1, 25, or 30)
• #17 Faucet Bibb Screw 1/2 X 10-24
• #2 Faucet Bibb Screw 1/2 X 6-32
• #4 Faucet Bibb Screw 3/8 X 8-32 (this size is also available in a pack of 3)

These screws are used to secure the handle to the faucet fixture after repairing a leaky faucet. Danco also offers an outdoor faucet water spigot handle that includes bibb screws and adapters for simple installation.

Danco #46 faucet handle screw

The Danco #46 faucet handle screw is a durable metal screw designed for easy installation and reliable performance. It measures 0.5 inches in length and 0.1 inches in width and height. This screw is a convenient and cost-effective solution for restoring and installing faucet handles, as you can simply replace the screw instead of the entire handle.

Danco offers a wide range of faucet handle screws, including the #46 screw, which vary in length, gauge, and head style. These screws are crafted from durable materials to ensure strength and reliability.

If you are unsure about which screw is suitable for your faucet handles, Danco provides specific screws designed for common brands such as American Standard, Gerber, and Price Pfister. Additionally, they offer a faucet handle screw kit that includes two screws each of five different sizes, ensuring you find the right fit for your project.

It is important to note that the Danco #46 faucet handle screw contains chemicals, including lead, which is known to the State of California to cause cancer and reproductive harm.

Frequently asked questions