
The Game Boy Advance requires a specific set of tools for repairs, modifications, and maintenance. To remove the screws securing the case, you'll need a Y1 Tri-point screwdriver or a Y1 screwdriver and a JIS 1 screwdriver. For the GBA SP, a JIS00 screwdriver or a PH00 screwdriver along with a Y00 Tri-point screwdriver are required. It's important to note that iFixit's Phillips screwdrivers are designed to work with JIS screws, but non-iFixit Phillips screwdrivers may be more challenging to use. Additionally, when choosing a screwdriver, it's recommended to follow best practices to avoid stripping screws, such as using the largest driver size that fits snugly.
Characteristics | Values |
---|---|
Screw Type | Tri-point or Tri-wing |
Screwdriver Size | Y1 |
Other Names | Tri-point, Tri-wing, Y-type |
What You'll Learn
Tri-wing vs. Tri-point (Y)
When it comes to the Game Boy Advance, there seems to be some confusion about whether you need a tri-wing or a tri-point (Y) screwdriver to open the console and access the cartridges. This is understandable given that different sources refer to the Y-type screw used in Game Boys as either a "tri-point" or a "tri-wing".
IFixit, for example, refers to the Y-type screw as a "tri-point", while Amazon and other websites commonly label it as a "tri-wing". However, according to iFixit, an actual tri-wing screw has three slotted "wings" and a small triangular hole in the centre, with the slots offset and not intersecting the centre of the fastener. This type of screw is not used in Game Boys.
To clarify, if you want to open a Game Boy Advance or access its cartridges, you will need a tri-point screwdriver, specifically a Y1 screwdriver for the console and a Y0 screwdriver for the cartridges. Additionally, the Game Boy Advance also requires a JIS 1 screwdriver, or an official iFixit Phillips #1 (PH1) screwdriver, to remove the screws on the cover.
CKRT Screw Size: Understanding the Standard
You may want to see also
Screwdriver compatibility
To open a Game Boy Advance, you will need a Y1 screwdriver and a JIS 1 screwdriver, or an official iFixit Phillips #1 (PH1) screwdriver to remove the screws on the cover. The Y1 screwdriver has a Y-shaped tip with three wings. The JIS 1 screwdriver is also known as a Phillips #1 screwdriver.
If you are looking to open a Game Boy Advance SP, you will need a JIS00 screwdriver, or an official iFixit PH00 screwdriver and a Y00 Tri-point screwdriver to remove the screws securing the case. The Y00 Tri-point screwdriver is also known as a Tri-Wing screwdriver and has a Y-shaped tip with three wings.
Some people have reported that the Y1 screwdriver is too big for the Game Boy Advance. In this case, you may need a smaller size such as a Y0.6 or a Y2.0. It is important to note that the screws on the Game Boy Advance and the Game Boy Advance SP are different sizes, so make sure you have the correct screwdriver for the correct console.
There are also screwdriver sets available that include multiple sizes and types of screwdrivers, which can be useful if you are working on multiple consoles or are unsure of the exact size you need. These sets typically include a range of Tri-Wing and Phillips-head screwdrivers, as well as other tools that may be useful for repairing and modifying your console.
The Perfect Screw Size for Your Focus RS Airbox
You may want to see also
Screw size discrepancies
When it comes to the Game Boy Advance, knowing the correct screw size is essential, especially when performing repairs or modifications. However, there seems to be some discrepancy and confusion regarding the exact size of the tri-wing screws used in the Game Boy Advance.
Some sources claim that the correct size for the tri-wing screws in the Game Boy Advance is Y1. This is supported by iFixit, a reputable repair website, which states that the Game Boy Advance requires a Y1 screwdriver to remove the screws on the cover. Additionally, an Amazon product listing for a set of tri-wing screws and a screwdriver specifically mentions compatibility with the Game Boy Advance, and the screws appear to be of the Y or tri-wing variety.
On the other hand, some users on forums and discussion boards have reported that the Y1 size is too big for the Game Boy Advance. These users suggest that smaller sizes, such as Y0.6 or Y2.0, may be more appropriate. It is worth noting that the Y1 size is indeed larger than the Y0.6 and Y2.0 sizes, which could explain why some users have encountered issues.
Adding to the confusion, there is a distinction between tri-point and tri-wing screw types, which are different names for the same type of screw. Nintendo refers to this screw type as tri-point, while it is commonly known as tri-wing on Amazon and other websites. This discrepancy in terminology may further contribute to the size confusion.
To complicate matters, there are also reports that the Game Boy Advance SP, an upgraded version of the Game Boy Advance, uses even smaller screw sizes. According to iFixit, the GBA SP requires a JIS00 or PH00 screwdriver, which are significantly smaller than the Y1 size. This suggests that the screw sizes may vary between different models or revisions of the Game Boy Advance.
Given the conflicting information, it is advisable for individuals working with Game Boy Advance screws to be cautious and consult multiple sources to ensure they have the correct screw size and type for their specific model and situation.
Choosing the Right Bit Size for Your 1/4-Inch Tapcon Screw Project
You may want to see also
Screwdriver bit sizes
When it comes to the Game Boy Advance, knowing the correct screwdriver bit sizes is essential for maintenance, repairs, or modifications. The type of screws used in the Game Boy Advance can be a source of confusion, as they are often referred to as both "tri-point" and "tri-wing."
To clarify, the correct screwdriver bit size for the Game Boy Advance is Y1. This is specified by iFixit, a reputable source for repair information. This Y1 screwdriver bit is required to remove the screws securing the case of the console. It is important to note that this is different from the screwdriver size needed for the GBA SP, which is a newer model requiring a smaller bit size.
The distinction between "tri-point" and "tri-wing" screw types can be a source of confusion. According to iFixit, the Y-type screw is technically referred to as a "tri-point." However, on platforms like Amazon and other websites, it is commonly called a "tri-wing." To further complicate matters, an actual tri-wing screw has distinct characteristics: three slotted "wings" and a small triangular hole in the center, with the slots offset and not intersecting the center of the fastener.
When working with Game Boy Advance screws, it is crucial to use the correct screwdriver bit size and type. Using an incorrect screwdriver can result in damage to the screws and the device. Additionally, it is recommended to follow best practices, such as using the largest driver size that fits snugly into the screw, to avoid stripping the screws.
In summary, for the Game Boy Advance, the screwdriver bit size required is Y1, which is considered a tri-point type of screw by iFixit. This information will be valuable for anyone looking to perform maintenance, repairs, or modifications on their Game Boy Advance console.
The Right Fit: Understanding Standard Doorknob Screw Sizes
You may want to see also
Screwdriver sets
To open a Game Boy Advance, you will need a Y1 screwdriver and a JIS 1 screwdriver, or an official iFixit Phillips #1 (PH1) screwdriver to remove the screws on the cover.
If you are looking to purchase a screwdriver set, there are a variety of options available. Here are some detailed suggestions:
Magnetic Screwdriver Sets:
- The Amartisan 10-piece set includes 5 Phillips and 5 Slotted tips with a professional cushion grip.
- The 6PCS Magnetic Tip Screwdriver Set offers 3 Phillips and 3 Flat head screwdrivers with a professional cushion grip.
- The Amartisan 43-piece set includes Slotted, Phillips, Hex, Pozidriv, Torx, and Precision Screwdriver types, along with magnetizer and demagnetizer tools.
- The SUNHZMCKP 66-piece set is made of S2-Alloy Tool Steel and includes Slotted, Phillips, and Torx Mini Precision Screwdriver types.
- The HORUSDY 11-piece set includes 5 Phillips and 5 Flat Head tips with a magnetizer, demagnetizer, and a precision screwdriver.
- The SWANLAKE 11-piece set offers 5 Phillips and 5 Flat Head tips for fastening and loosening seized screws.
High-Torque Screwdriver Sets:
TEKTON offers a range of High-Torque Screwdriver Sets with 2, 4, 8, 10, 12, 16, 22, and 58 pieces. These sets come with various features, such as black oxide blades, red or black rails, and a rack or holder for storage.
Insulated Screwdriver Sets:
- The Milwaukee 3-piece set is 1000-volt insulated.
- The Klein Tools 6-piece set is also 1000-volt insulated and includes a magnetizer/demagnetizer for magnetic tips.
Other Varied Screwdriver Sets:
- The Wera 6-piece set includes multicolored screwdrivers with lasertip technology.
- The Klein Tools 7-piece set features non-slip cushion-grip handles and a tip-ident system.
- The CRAFTSMAN 2-piece set has bi-material handles.
- The CARTMAN 12-piece set includes 6 Phillips and 6 Flat head screwdrivers with a professional cushion grip.
- The Milwaukee 8-piece set includes Phillips, Flat Head, and Square Hex Drive Screwdrivers with a Tri-Lobe handle.
- The Husky 10-piece set features Diamond Tip Magnetic Screwdrivers.
These suggestions offer a range of screwdriver sets that can be useful for various tasks, including working on a Game Boy Advance.
Stodis Shelf Screw Size Guide
You may want to see also
Frequently asked questions
You will need a Y1 screwdriver and a JIS 1 screwdriver, or an official iFixit Phillips #1 (PH1) screwdriver to remove the screws on the cover.
Tri-point screwdrivers have three tips and are used for the original Game Boy and Game Boy Color. Tri-wing screwdrivers have three slotted "wings" and a small triangular hole in the centre.
You will need a Y0 Tri-point screwdriver to open GBA cartridges.