G&L Saddle Height: Intonation Screw Size Matters

g&l saddle height intonation screw size

G&L ASAT Classic guitars come with a set of six brass saddles, complete with bridge mounting screws, saddle height adjustment screws, intonation screws, and springs. The intonation screw size on the G&L ASAT Classic is 3mm, while the hex wrench size for the height adjustment screw is 1.5mm. G&L saddle lock bridges have a #0 Phillips screw, which is one size smaller than the screw used for pickguard screws.

shuntool

G&L ASAT Classic bridge saddle set

The G&L ASAT Classic bridge saddle set is a set of six brass saddles designed for the G&L ASAT Classic bridge. It comes with bridge mounting screws, saddle height adjustment screws, intonation screws, and springs. The height adjustment screws have two screws per saddle, and the intonation screws have one long screw per saddle. The set fits all USA and Tribute Series ASAT Classic models and most Fender® USA and similar vintage spec Telecaster® models.

The G&L ASAT Classic bridge saddle set is designed to improve intonation and sustain. The bridge plate is modified to make room for the pivot bolts for models with either Dual-Fulcrum Vibrato or Leo Fender Vibrato. The bottom side of the bridge has a large protrusion that fits snugly against the end grain of the body wood, allowing for greater resonance and sustain.

The G&L ASAT Classic bridge saddle set is a direct replacement for the non-G&L vintage bridge with three brass saddles found on the ASAT JD-5 model, which was available for a short time in 2004. The six independent saddles of the G&L ASAT Classic bridge saddle set provide a solution to the intonation problems of the three-saddle design.

The G&L ASAT Classic bridge saddle set is available for both right-handed and left-handed versions of the ASAT Classic bridge. The set is sold by the G&L Online Store for $27.95 USD, with a sale price of $15.00 USD at the time of writing.

shuntool

Adjusting intonation on a G&L Saddle lock bridge

Adjusting the intonation on a G&L Saddle Lock bridge can be done by following these steps:

First, make sure you have the right screwdriver for the job. The intonation screws on a G&L Saddle Lock bridge are Phillips head screws, so you'll need a #0 Phillips screwdriver. This is one size smaller than what you would typically use for pickguard screws, and it should have a small diameter handle to allow for easy manoeuvring.

Before making any adjustments, it's important to loosen the saddle lock screw. This is the allen head screw located on the side of the bridge assembly. Once loosened, you can then adjust the individual saddles. Each saddle has two height adjustment screws located at the top, which can be adjusted using an allen wrench.

After you've made the necessary height adjustments, you can then intonate the strings. This is done by accessing the intonation screw through the hole in the back of the bridge assembly. Remember to tighten the saddle lock screw again once you've finished adjusting the intonation.

If you're having trouble lowering the action, make sure the side screw is loose enough to turn freely. If it's too tight, it can prevent the individual saddles from moving independently. You can also try pinching the string just beyond the saddle and wiggling it side-to-side to loosen any saddles that may be stuck together.

Finally, once you've adjusted the height and intonation to your liking, lightly tighten the side screw to lock the saddles together. This will ensure that they vibrate as one big mass, improving the sustain and tone of your guitar.

shuntool

#0 Phillips screwdriver for G&L Saddle lock bridge

If you're looking to adjust the intonation on your G&L Saddle Lock bridge, you'll need a #0 Phillips screwdriver. This is one size smaller than what you would use for pickguard screws, and you'll want to make sure it has a small diameter handle to keep it close to the body of your guitar.

You can find #0 Phillips screwdrivers marketed as 'precision' screwdrivers, and you don't need to spend a lot of money on them. A basic set of precision screwdrivers should do the trick, and you can find them at your local dollar or hardware store. Just make sure that the set includes a #0 Phillips.

When making adjustments to your G&L Saddle Lock bridge, remember to loosen the saddle lock screw on the side of the bridge assembly before adjusting the individual saddles. Each saddle has two height adjustment screws at the top, and the intonation screw is accessible through the hole in the back of the bridge. After you've made your adjustments, be sure to re-tighten the saddle lock screw.

It's also worth noting that, depending on the model and year of your guitar, you may need to measure the interior width of your bridge plate to ensure that any replacement saddles will fit.

shuntool

G&L intonation screw size

G&L manufactures guitars and basses. The intonation screw size for G&L instruments varies depending on the model and year of manufacture.

G&L Tribute Series

For G&L Tribute instruments and USA instruments manufactured from 2006 onwards, the tension screw set is metric.

G&L Pre-2005 Models

For US instruments 2005 and older, the tension screw set is not metric.

G&L L-2000

For the G&L L-2000, the saddle intonation screws are M4 .7 x 30 Phillips drive fillister head machine screws. The thread pitch is .7, and the length is 30mm.

G&L ASAT Classic

The intonation screws for the G&L ASAT Classic are 3mm in thread size.

G&L Legacy USA

The intonation screws for the DF tremolo on the 1997 Legacy USA model are #4-40 X 5/8" in size.

It is important to note that the correct intonation screw size for a G&L instrument can vary, and it is always best to consult an expert or a G&L representative for specific models and years.

shuntool

MIM Standard Tele saddle height adjustment screws

The MIM Standard Tele saddle height adjustment screws are used to raise or lower the saddle of your guitar to accommodate different gauge strings. These screws are available in a variety of lengths to fit your guitar-playing needs.

For a current production MIM Standard Tele with a modern 6-saddle bridge, the hex wrench size for the height adjustment screw is 1.5mm. The exact size of the height adjustment screw depends on your particular guitar setup.

The most common setup is to use shorter-length saddle height screws on the little E and big E string saddles, with the middle saddles using the next size larger. The reason for the different lengths is to set the radius of the saddles to closely approximate the radius of the fretboard without having excessive screw length protruding above the saddles, which can cause discomfort while playing.

For a Fender MIM Stratocaster, the saddle height adjustment screws are metric M3x.5, with a length of either 6mm, 8mm, or 10mm. These screws have a cup point and are made of stainless steel to prevent rust and corrosion.

If you are looking for shorter saddle height adjustment screws for your MIM Strat, you can try sources such as Angela Instruments and Guitar Parts Resource, or consider purchasing replacement screws from Bolt Depot, which offers a range of sizes and lengths. You can also modify the existing screws by grinding them down to the desired height.

It is important to note that the height of the saddles above the bridge is not specified in Fender's documentation, but it is generally recommended to keep the excess height of the screws above the saddle as short or flush as possible.

Frequently asked questions

The intonation screws for the G&L ASAT Classic have a 3mm thread size.

A #0 Phillips screwdriver is needed to adjust the intonation on the G&L Saddle lock bridge.

The hex wrench size for the saddle height adjustment screw on a MIM Standard Tele is 1.5mm.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment