A Step-By-Step Guide To Changing Blades On Your Jet Table Saw

Changing the blade on a table saw is a straightforward process but it's important to follow the correct safety procedures. Before you start, make sure the saw is unplugged and turned off. You should also consult the user manual for your specific model of the table saw.

Unplug the saw and remove the blade guard

Unplugging the saw is the first step to take when changing the blade on your Jet Table Saw. This is a crucial safety precaution to prevent any accidents or injuries. Once the saw is unplugged, you can proceed with removing the blade guard.

The blade guard is a protective cover that surrounds the blade of the table saw. It is important to remove the blade guard to access the blade for replacement. On a Jet Table Saw, the blade guard can be removed by loosening or unscrewing the fasteners that hold it in place. Make sure you have a clear understanding of the mechanism and refer to the owner's manual if needed.

After removing the blade guard, you will have better access to the blade and the arbor, which is the shaft that holds the blade in place. It is important to exercise caution when handling the blade and its components to avoid injury. Wear safety gloves if possible.

Before proceeding further, it is essential to ensure that the saw is securely unplugged and there is no chance of accidental activation. This step cannot be overemphasized, as accidentally turning on the saw while your hands are near the blade can lead to severe injuries. Always prioritize safety when working with power tools.

With the saw unplugged and the blade guard removed, you can now access the blade more easily. The next step is to raise the blade to its highest point, which will make it easier to remove. You can do this using the crank or wheel located near the blade. By raising the blade, you create the necessary space to work on removing and replacing the blade effectively.

In summary, unplugging the saw and removing the blade guard are crucial steps in changing the blade on a Jet Table Saw. These steps prioritize safety and provide access to the blade for replacement. Always refer to the owner's manual for specific instructions and take your time to ensure a safe and successful blade change.

Take off the throat plate and table pin

To take off the throat plate and table pin of a Jet table saw, you'll need to follow a few simple steps.

First, make sure your table saw is unplugged and turned off. This is an essential safety precaution. Once the power is off, locate the throat plate and table pin. The throat plate is the metal part of the saw that surrounds the blade, and the table pin is a small pin that holds the throat plate in place.

To remove the throat plate, you may need to unscrew any fasteners or thumbscrews holding it in place. Be sure to keep these screws in a safe place so you can put them back later. With the screws removed, gently lift or wiggle the throat plate to remove it. Set it aside in a safe place.

Now, for the table pin. This is typically a press fit, so you can use a pair of pliers to gently pull it out. Again, be careful not to apply too much force, as you don't want to damage the pin or the surrounding area. Once the table pin is removed, set it aside with the throat plate.

With these two parts removed, you'll have better access to the blade and other internal components of the saw. Remember to refer to the owner's manual for your specific model of Jet table saw, as there may be slight variations in the process.

Raise the blade to its highest point

To change the blade on a Jet table saw, you must first raise the blade to its highest point. This is done to give you the easiest access to the blade when you come to removing it.

To do this, first ensure your table saw is unplugged and turned off. Then, remove the throat plate and blade guard. With these safety features removed, you can then raise the blade to its highest point using the crank.

It is important to consult your user manual before attempting to change the blade, as each model is different.

Loosen the arbor nut and washer with a wrench

To loosen the arbor nut and washer with a wrench, follow these steps:

First, ensure that your table saw is unplugged and turned off. This is a crucial safety precaution when working with power tools. Next, remove the throat plate and blade guard. This step may vary depending on the model of your table saw, so refer to the instruction manual if needed. With the throat plate and blade guard removed, proceed to raise the blade to its maximum height. This step provides easier access to the arbor nut and washer.

Now, locate the arbor nut and washer. The arbor is the shaft that the blade is mounted on, and it is secured in place with the arbor nut and washer. To loosen the arbor nut, you will need a pair of wrenches. One wrench is used to hold the arbor and the blade immobile, while the other wrench is used to turn and loosen the arbor nut on the opposite side. Apply force in opposite directions on each side with the wrenches.

Alternatively, if your table saw has an arbor lock, you can use that instead. In this case, push down on the arbor lock with one hand while using the other hand to loosen the arbor nut with a wrench. Once the arbor nut is loose, hold onto it and slowly rotate it with your thumb and index finger to finish removing it. Be careful not to drop the arbor nut or washer into the table saw.

Put a new blade on, tighten, and replace the plate

To put a new blade on your Jet table saw, you must first ensure that the saw is unplugged and turned off. Then, remove the throat plate and blade guard. You can do this by unscrewing the fasteners holding the throat plate. Next, raise the blade to its highest point using the crank, so that it is fully visible and easy to access.

Now, you need to remove the old blade. The blade is mounted on an arbor, which is a shaft that holds the blade in place with an arbor nut and a washer. Loosen the arbor nut with a wrench, and then finish removing it by hand. Once the nut is removed, take off the washer and carefully lift out the old blade, placing it on your work surface.

With the old blade removed, you can now install the new blade. Place the new blade onto the arbor, ensuring that it is facing the correct way. The teeth of the blade should be pointing towards you. Once the blade is in place, replace the washer and the arbor nut, and tighten them securely.

Finally, replace the throat plate and blade guard. Your new blade is now ready to use.

Frequently asked questions