Choosing The Right Screwdriver For Adjusting Whirlpool Cooktop Flames

To adjust the flame on a Whirlpool gas stove, you will need a screwdriver. The size of the screwdriver will depend on the type of stove you have. For a standard burner, you will need to adjust the screw in the valve stem's centre, which is located under the control knob. For a low flame, you will need to remove the control knob and use a flat-blade screwdriver to turn the screw until you reach the desired flame size. For a double burner, you will need a 3mm flat-blade screwdriver to rotate the slotted screw.

Adjusting the standard burner

It is important to note that the low burner flame should be flue and have a height of 0.64 cm. If you are using LP gas, the flame will have a yellow tip.

Adjusting the low flame

Step 1: Light the First Burner

Firstly, light up the first burner and set it to the lowest possible setting.

Step 2: Remove the Control Knob

Now, you need to take out the control knob. For this, you will require pliers to hold the knob stem.

Step 3: Adjust the Flame

Next, use a flat-blade screwdriver to turn the screw until you achieve the desired flame size. Remember, turning the screw in a clockwise direction will increase the flame's size, while turning it counterclockwise will reduce the flame.

Step 4: Replace the Control Knob

Once you are happy with the flame size, replace the control knob.

Step 5: Test the Flame

Finally, test the flame by adjusting the control knob from low to high settings. Check the flame size at each setting.

Repeat these steps for each burner on your cooktop.

Adjusting the double burner

Step 1: Light the Burner and Set to Lowest Setting

First, light any burner on the stove and adjust it to the lowest possible setting to ensure that the outer and inner burners are lit properly.

Step 2: Remove the Control Knob

Use a pair of pliers to hold the knob stem and carefully remove the control knob. This will expose the valve stem, which is where you will make the necessary adjustments.

Step 3: Adjust the Flame with a Screwdriver

For this step, you will need a 3mm flat-blade screwdriver. Locate the slotted screw in the valve stem and rotate it to adjust the flame size. Turning the screw clockwise will increase the flame, while counterclockwise rotation will reduce it. Make sure to adjust the flame to your desired size.

Step 4: Replace the Control Knob and Test

Once you are happy with the flame size, carefully replace the control knob. Now, it's time to test your work. Adjust the control knob from low to high settings and observe the flame at each position. Ensure that the flame responds accordingly to your adjustments.

Troubleshooting:

If the flame is not responding as expected to your adjustments, there might be a simple fix. First, check if the burner ports are clogged with grease or debris, as this can interfere with the flame. Use a thin wire, straight pin, or needle to clear any blockages. Additionally, ensure that the burner base and cap are properly positioned and seated correctly on the base.

The flame is not responding to the settings

If the flame is not responding to the settings, there are a few things you can try. First, make sure the burners are clean. It's common for burners to get clogged with grease and debris with regular cooking. You can use a thin wire, a straight pin, or a needle to clear the burner ports if they are clogged. Also, check the burner base and cap to make sure they are positioned properly. The burner base must be seated properly on the base to ensure proper lighting.

Adjusting the flame on a propane gas stove

Adjusting the Standard Burner:

If you need to adjust the standard burner on your gas stove, you can do so by regulating the adjustment screw located in the centre of the valve stem, which is right below the control knob.

Adjusting the Low Flame:

To adjust the low flame on your propane gas stove, follow these steps:

• Light up the first burner and select the lowest possible setting.
• Remove the control knob using pliers to hold the knob stem.
• Use a flat-blade screwdriver to turn the screw until you achieve the desired flame size. Turning the screw clockwise will increase the flame, while turning it counterclockwise will reduce the flame.
• Replace the control knob and test the flame by adjusting the control knob from low to high settings. Check the flame size at each setting.
• Repeat these steps for each burner.

Adjusting the Double Burner:

If your propane gas stove has a double burner, follow these steps for adjustment:

• Light any burner and adjust it to the lowest setting to ensure that the outer and inner burners are lit properly.
• Remove the control knob.
• Use a 3mm flat-blade screwdriver to rotate the slotted screw. Turning the screw clockwise will increase the flame, while turning it counterclockwise will reduce the flame.
• Replace the control knob.
• Test the flame size by rotating the control knob from low to high and checking the flame at each position.

Troubleshooting:

If the flame is not responding to your adjustments, it may be due to clogged burners. Clean the burners and ensure that the burner base and cap are positioned correctly.

Additionally, when adjusting the flame, make sure to use the appropriate screwdriver size and follow the manufacturer's instructions for your specific model of the propane gas stove.

Frequently asked questions