Choosing The Right Screw Size For S&W Rear Sight Leaf

The Smith & Wesson revolver line includes the K, L, X, and N frame models chambered in various calibres. The rear sight leaf screw for these models is constructed from quality steel and is designed to retain the rear sight leaf during operation. The screw size for the original sight leaf screw is important for gun maintenance and repairs, and it is recommended that all Smith & Wesson parts be installed by a qualified and trained gunsmith.

Screw size for old-style rear sight N-frame

The screw size for an old-style rear sight N-frame can vary depending on the specific model of Smith & Wesson firearm. The N-frame models typically refer to the large-sized revolvers in the Smith & Wesson lineup, and the rear sight leaf screw is an important component for retaining the rear sight leaf during operation.

For the Smith & Wesson K/L/N/X-Frame revolver line, the rear sight leaf screw is constructed from quality steel and is manufactured as an OEM factory original part. This particular screw is recommended to be installed by a qualified and trained gunsmith. It is designed to fit various N-frame models chambered in calibers such as .41 Rem Mag, .44 Special, and .45 Colt, among others. The finish for this screw is black, and it is intended for use with pistols.

In terms of specific screw sizes, one source suggests that a 3-56 screw may fit the sight of an old-style rear sight N-frame, although other sizes mentioned include 6-48 and 4-48. It is important to note that these sizes may vary depending on the specific model and that a gunsmith should be consulted for proper installation and sizing.

Additionally, it is worth mentioning that there are rear sight leaf screws available for both old-style and new-style leafs. The old-style screws are designed for leafs with square fronts, while the new-style screws are intended for leafs with round fronts. Ensuring the correct style of screw is essential for proper fit and function.

S&W K/L/N/X-Frame rear sight leaf screw

The screw size for the rear sight leaf of a Smith & Wesson revolver will depend on the specific model and its features.

Smith & Wesson N-Frame

The screw size for the rear sight leaf of an older Smith & Wesson N-Frame revolver is reported to be 3-56, 4-48, or 6-48.

Smith & Wesson K/L-Frame

The Smith & Wesson K/L-Frame revolver series includes a range of models, such as the 10, 11, 12, 13, 14, 15, 16, and many others. While I could not find specific information on the rear sight leaf screw size for these models, online retailers offer spring kits and grip accessories tailored to the K/L-Frame series, indicating that these models share certain standard components.

Smith & Wesson X-Frame

Unfortunately, I could not find specific information on the rear sight leaf screw size for the Smith & Wesson X-Frame revolver.

For a more precise answer regarding your specific Smith & Wesson revolver model, it is recommended to consult a gunsmith or a specialised forum.

M&P rear sight screw size

The rear sight screw for the Smith & Wesson M&P M2.0, 9, 40, and 45 is a set screw that secures the rear sights to the slide of the firearm. The screw is made of strong steel and has a matte blued finish. It is recommended that all Smith & Wesson parts, including this screw, be installed by a qualified and trained gunsmith.

The rear sight set screw for the Smith & Wesson M&P comes in different sizes depending on the specific model of the firearm. For the M&P M2.0, 9, 40, and 45, the rear sight screw has a larger girth compared to the M&P 1.0. This difference in size is important to note when replacing the rear sight, as the M2.0 screw will not fit into the smaller hole of the M&P 1.0 rear sight.

When removing or installing the rear sight screw, it is important to use the correct tools. Some sources suggest that a 1/16" hex key or Allen wrench is the appropriate size for the job, while others recommend using a Torx screwdriver with a "CR-VT7" tip. It is worth noting that the Torx size may be denoted as "CR-VT6" on some tools. Before attempting any adjustments, it is advisable to refer to the instructions provided by Smith & Wesson or seek the assistance of a qualified gunsmith.

Additionally, applying direct heat to the screw with a soldering iron or similar tool can help loosen any thread-locking compound, such as Loctite, that may have been used during manufacturing. This can make it easier to remove the screw without stripping it.

It is always recommended to exercise caution and follow proper safety procedures when working with firearms.

Sights not designed to be held by set screw

When it comes to firearms, it is essential to understand that sights are crucial components for accurate shooting. While sights come in various shapes and sizes, they are typically designed to be adjusted to the user's preferences. This adjustment is often achieved through the use of screws, which allow for precise windage and elevation changes.

However, it is important to recognise that not all sights are designed to be held in place solely by a set screw. In some cases, sights may utilise other mechanisms or designs to ensure their stability. For instance, certain sights might be attached using a dovetail design, where the sight is slid into a corresponding cut-out on the firearm and secured in place by friction or additional hardware. This method does not rely on a set screw for retention.

Additionally, some sights may be integrated directly into the firearm's design, becoming a permanent fixture that cannot be adjusted or removed. These sights are typically machined or moulded into the firearm's construction, eliminating the need for screws or other adjustable hardware.

It is also worth noting that some sights may utilise a combination of set screws and other attachment methods. For example, a sight may have a set screw to allow for windage adjustments while also being secured in place by a dovetail design or a locking mechanism.

Understanding the specific design of your firearm's sights is crucial. If you attempt to adjust or remove a sight that is not designed to be held by a set screw, you may cause damage to the firearm or the sight itself. Always refer to the manufacturer's instructions or seek the expertise of a qualified gunsmith when making any modifications or adjustments to your firearm's sights.

Smith & Wesson revolver line

Smith & Wesson was founded in 1856 as the "Smith & Wesson Revolver Company" and has since become an iconic American firearm manufacturer. The company's revolver designs have been in high demand since the American Civil War, with the Smith & Wesson Model 1 outpacing the factory's production capabilities by 1860.

Over the years, Smith & Wesson has released numerous revolver models, including:

• Model 1: The first Smith & Wesson revolver, which experienced high demand during the American Civil War.
• Model 3: Introduced automatic ejection of spent cartridge cases and featured in a variety of calibers, including .44 Russian and .44 S&W Special.
• Model 10: Previously known as the ".38 Military & Police" and ".38 Victory Model," this model is chambered in .38 Special.
• Model 29: Made famous by its appearance in the film Dirty Harry, this model is chambered in .44 Magnum.
• Model 57: The first .41 Magnum revolver, sponsored by Elmer Keith and others.

In addition to these classic models, Smith & Wesson continues to innovate with new revolver designs, as evidenced by their extensive list of Performance Center models on their website.

Regarding the rear sight leaf screw for Smith & Wesson revolvers, the specific screw size depends on the model and style of the revolver. For newer models with round front sights, a Smith & Wesson Rear Sight Leaf Screw for New-Style Leafs is available. For older models, the screw size may vary, with some sources suggesting 6-48, 4-48, or 3-56 as possible thread sizes.

It is important to identify the specific model and style of your Smith & Wesson revolver to determine the correct rear sight leaf screw size and ensure a proper fit.

Frequently asked questions