The Right Screw Size For Your Xbox One Power Supply

If you're looking to repair or replace your Xbox One power supply, you'll need to know the right screw size to open it up. The Xbox One power brick uses a variety of screw sizes, including T10, #0 Phillips head, and #1 Phillips head. For the Xbox One X Project Scorpio Edition, a T9 Torx screwdriver is needed to remove the screws. As for the Xbox 360 S power brick, an anti-tamper 8 Torx bit is required. It's important to be cautious when handling electronics and only proceed if you're confident in your abilities.

Screw sizes for Xbox One X power supply

To replace the power supply of the Xbox One X, you will need a T9 Torx screwdriver. This screwdriver will be used to remove the 13mm screw found under and to the left of the power input, the two 15mm silver screws, the 9mm black screw, the two 7mm screws, the six 47mm long screws, the four 11mm screws, the two 11.4mm screws, the two 8.6mm screws, and the two screws located on opposite sides of the metal casing (one is 11mm and the other is 7.5mm).

Additionally, you will need a Phillips head screwdriver to remove the two larger screws and the two smaller screws inside the power brick.

Please note that opening your Xbox may void your warranty. Always exercise caution when working with electronics, and ensure that you are grounded to prevent electrostatic discharge, which can damage internal components.

Screwdriver type for Xbox One power supply

To open up your Xbox One power supply, you will need a few different screwdrivers.

Firstly, you will need a T10 security bit driver to remove the four screws on the outside of the power brick.

Once you have removed the rubber boots, you will need a Phillips-head screwdriver to remove the two larger screws inside. A #1 Phillips-head screwdriver is recommended for the two smaller screws, as they are screwed down very tight.

If you are working on an Xbox One X, you will also need a T9 Torx screwdriver to remove the screws inside the console.

Xbox One power supply disassembly

To disassemble an Xbox One power supply, follow these steps:

Firstly, remove the rubber boots. This can be done by getting your fingernails underneath and gently pulling them up. If this is difficult, try using a twisting motion while prying them up.

Next, remove the four screws with a T10 security bit driver.

Now, disconnect the fan cable. Be careful not to touch the capacitor wires. Use a capacitor discharge probe to rid the capacitors of any dangerous charges. Gently pull the cable up and away from the circuit board.

Remove the two larger screws with a Phillips-head screwdriver. Then, remove the two smaller, tightly-screwed orange screws. A #1 Phillips head is recommended for these.

Once the screws are removed, lift the plastic frame from the left side and remove it from the top of the power brick. Flip the brick over.

Now, lift the fan from the side furthest away from the cable. Pull the cable through the hole in the frame and place the fan to the side.

Remove the four screws using a #0 Phillips head and remove the top of the fan housing. Gently grab the fan and lift it up.

Finally, give the inside of the power brick a clean. A can of air duster can be used to blow dust away.

Xbox 360 power brick screw size

To open an Xbox One power brick, you will need a T10 security bit driver and a Phillips-head screwdriver.

Now, for the Xbox 360 power brick. The screw bit size depends on the model of your Xbox 360. For the Xbox 360 S power brick, you will need a Torx bit. Specifically, an anti-tamper 8 or a T10. If you use a T10, you will need to hammer down the pins.

For the Xbox 360 Slim power supply, you will need a Phillips-head screwdriver.

If you are still unsure about which screwdrivers or screw bits to use, you can refer to the product manuals or the manufacturer.

Xbox 360 power brick disassembly

To disassemble your Xbox 360 power brick, you will need to follow these steps:

Firstly, ensure your Xbox is unplugged and switched off. It is very important that you do not work on the power supply while it is still connected.

Now, let's begin the teardown:

Step 1:

Remove the rubber feet on the bottom of the power brick. These can be popped out fairly easily and probably won't require any tools. Once removed, you will see small plastic inserts in their place. These can be pried out with a blade or a small screwdriver.

Step 2:

With the power brick bottom-up, remove four Phillips-head screws. Then, pull off the bottom half of the plastic shell. Next, locate and remove a single screw hidden between the light and the output cord. This screw secures the heatsink to the power supply. There is also a small, two-wire connector for the fan that should be removed carefully.

Step 3:

To access the fan, remove the metal heatsink from the plastic case. There are two screws at each end and two in the middle under the plastic layer. Be careful not to disturb the thermal paste underneath.

Step 4:

Clean the fan by blowing on it or using compressed air. Ensure all dust is removed, and clear any dust from the heatsink fins.

Step 5:

Reassemble the power brick by spreading thermal paste over the parts that need to contact the heatsink. Reinsert the single screw that holds the heatsink to the power supply.

Step 6:

Place the plastic shell back on, ensuring the power cord and plastic inlet are fitted properly. Tighten the screws and press the plastic inserts and rubber feet back into place.

Your Xbox 360 power brick is now disassembled and cleaned! Remember to keep it in a well-ventilated area to prevent overheating and extend its lifespan.

Frequently asked questions