Yamaha Hinge Screw Thread: Standard Sizing For Your Yamaha

Yamaha is a well-known manufacturer of a variety of products, including motorcycles, outboard motors, and musical instruments. When it comes to hinge screw thread sizes for Yamaha products, it is important to specify the particular product and model in question. For example, the thread size for the clamping screw of a 50 hp 2-stroke TLRZ Yamaha outboard motor is 9/16, while the caliper bleed screw thread size for a late model of the Yamaha XS650 motorcycle is M8 x 1.25mm. It is always recommended to refer to the product's manual or seek advice from authorized Yamaha dealers or technicians to ensure the correct hinge screw thread size for your specific Yamaha product.

Yamaha outboard clamp screw thread size

The thread size of a clamping screw for a Yamaha outboard motor depends on the model. For example, the thread size for a 50 hp 2-stroke TLRZ Yamaha is 9/16", while the screw sent by Yamaha is 1/2".

Some Yamaha outboard motors use a 5/8"UC size threading, which is equivalent to 15.85mm. This size is used in the 6G1-43116, 6E0-43118, and 648-43114 clamp screw assembly set. However, some customers have noted that this size is incorrect for their Yamaha motors, so it is important to check the correct thread size before purchase.

In addition to the thread size, the length of the screw is also important to ensure a proper fit.

For a 2012 4HP Yamaha outboard motor, the part number for the clamp screw bolt assembly is 6E0-43116-01-00. This part number may be useful for ordering replacement parts.

When replacing the clamp screw assembly, it is important to consider the tools and techniques required for assembly. For example, some parts may need to be bradded, which involves expanding the end of a pin or threaded rod to hold it in place. This can be done using a rotational riveting machine or a hammer and chisel, depending on the specific part and access to the area.

It is always recommended to consult a Yamaha technician or a qualified professional for advice on the correct thread size and assembly procedure for your specific Yamaha outboard motor model.

Yamaha caliper bleed screw thread size

The caliper bleed screw thread size for a Yamaha XS650 model from 1977 to 1984 is M8 x 1.25mm. The thread size for the 1972-1976 models is M8-1.0mm.

The caliper bleed screw thread size for a Yamaha XJ650 Maxim model from 1980 to 1983 is M8 x 1.25mm. The thread size for the 1980-1983 Yamaha XS650 Special II is also M8 x 1.25mm.

It is important to note that the bleed screws for the 1972-1976 Yamaha XS650 models differ from those of the 1977-1984 models. The bleed screws for the earlier models had a finer thread.

When replacing a caliper bleed screw, it is crucial to use the correct thread size and length to ensure a proper fit and maintain the integrity of the brake system. It is always recommended to refer to the specific Yamaha motorcycle model and year when sourcing replacement parts.

Screw head sizes for hinge repairs

When repairing a hinge, it is important to use the correct screw head size to avoid aggravating the problem. An incorrect screw size can cause damage to the door or result in a sagging door. The standard hinge screw size for residential door hinges (such as bedroom or bathroom doors) is typically a #9 screw. For architectural door hinges used for main and entry doors, a #10 screw is often specified. Commercial door hinges, on the other hand, usually require a larger #12 screw.

To identify the correct screw head size for a hinge repair, you can measure the width of the screw head after removing the existing loose screws. This can be done with a measuring tape or a caliper. It is important to ensure that the length of the screw is also appropriate for the application. The screw length should be long enough to securely hold both the material and the hinge.

In addition to the screw size, the finish and material type of the screw are also important considerations. Screws are available in various finishes, such as satin nickel, black, brass, or oil-rubbed bronze, to match different hinges. The type of head design (countersunk or non-countersunk) and the thread design are also factors to consider when selecting the appropriate screw for a hinge repair.

For Yamaha-specific hinge screw sizes, there is limited information available. One source mentions a clamping screw for a 50 hp 2-stroke TLRZ Yamaha with a thread size of 9/16". However, it is unclear if this is the standard size for all Yamaha hinge screws.

Identifying hinge screw size

Identifying the correct hinge screw size for your door is essential to fix a loose door hinge. Using the wrong hinge screw size can aggravate the problem, whereas the right screw size saves time and fits perfectly.

There are many types of door hinges, and each requires a specific hinge screw size:

• Residential Door Hinges: These are the hinges used for residential bedroom and bathroom doors. The standard hinge screw size for a residential door hinge is a #9 screw.
• Architectural Door Hinges: These are the hinges used for the main doors and entryways of houses. The standard hinge screw size for an architectural door hinge is a #10 screw.
• Commercial Door Hinges: These are the hinges used for commercial spaces, such as office and building doors. The standard hinge screw size for a commercial door hinge is a #12 screw.

To measure the hinge screw size, you need to first remove the existing loose screws. Then, you can measure the width of the screw head using a measuring tape or a caliper.

It is important to note that the standard measurement of a screw size consists of both the head size and the shaft size. The length of the screws is measured in inches, for example, a "9X3" screw is 9 in size and 3 inches long. The length of the screw should be sufficient to hold both the material and the hinge securely.

Additionally, screws are designed with different finishes and head styles to match specific hinges and serve decorative or utilitarian purposes. Some common screw finishes include satin nickel, black, brass, or oil-rubbed bronze. The basic head designs are countersunk and non-countersunk. Countersunk head designs, such as flat heads, are flush with the surface material, while non-countersunk head designs, such as button, hex, and round, are visible and protrude from the surface.

Yamaha TLRZ clamp screw thread size

The thread size of the clamping screw for a 50 hp 2-stroke TLRZ Yamaha is 9/16". This is different from the MH model, which has a 1/2" thread size.

Some people opt to not use the clamp at all, instead bolting the outboard motor directly to the boat at the proper height.

For a 2001 Yamaha 90 TLRZ, the steering tube thread size is 7/8-14 unf.

There are also aftermarket clamp screw sets available for Yamaha outboards, such as the ITACO Boat Motor 6G1-43116 6E0-43118 648-43114 Clamp Screw Set. This set has a 5/8" UC size threading, which is equivalent to 15.85mm.

Frequently asked questions